Installation ManualLBI-38636SMASTR® IIIConventional Base Station
LBI-38636S11Figure 1 - Typical 37-inch MASTR III StationsSAFETY SUMMARYThe following general safety precautions must beobserved during all phases of o
LBI-38636S12DO NOT SUBSTITUTE PARTS ORMODIFY PRODUCTBecause of the danger of introducing additionalhazards, do not install substitute parts or perform
LBI-38636S13Figure 2 - 37 Inch Mounting FootprintFigure 3 - 37-Inch CabinetUsing the four holes are provided in the bottomsurface of the cabinet, the
LBI-38636S14ELECTRICAL CONNECTIONSAC PowerThe station will be received with the power cordbundled and stored in the bottom of the cabinet. Removethe t
LBI-38636S15less populated areas where the phone company has not yetswitched to carrier systems. These lines have a fixedamount of loss, which varies
LBI-38636S16
LBI-38636S17The telephone company wants to see a maximum three-second level of -13 dBm at the carrier equipment asmeasured on a modified Western Elect
LBI-38636S182. The loss of the circuit at 2175 Hz. Do not forgetthe long-term variation of up to 4 dB more.3. The requirement that the "Secur-i
LBI-38636S19Telephone Company Ordering InformationWhen ordering a telephone line, the following mustbe considered:1. Type of circuit:Voice grade, 2-w
LBI-38636S20Tone Remote InstallationJumpers P104 and P105 located on the InterfaceBoard are not required and should be removed. Refer tothe sections o
LBI-38636S3NOTERepairs to this equipment should be made only by an authorized service technician or facility designated by the supplier.Any repairs, a
LBI-38636S21Table 1 - Wire Line Installation MethodsMETHOD DESCRIPTION PROCEDURE ADVANTAGES ORDISADVANTAGES1 Single metallic pair (thecontrol currents
LBI-38636S22Figure 8 - METHOD 1 (Single Metallic Pair)Figure 9 - METHOD 2 (Single Metallic, Earth Ground)
LBI-38636S23Figure 10 - METHOD 3 (Metallic Control Pair, Audio Pair)Figure 11 - METHOD 4 (Full Duplex Metallic TX Pair)
LBI-38636S24Figure 12 - Telephone Line ConnectionsSTATION SETUPThe MASTR III station comes pre-programmed andready to install, the only adjustments ne
LBI-38636S25Table 3 - Station ConnectorsCONFIGURATION STATION TERMINATINGCONNECTORLOCATIONSimplex (T/R Relay) N-Type Female Antenna SwitchDuplex (Inte
LBI-38636S26ALIGNMENT PROCEDUREAlignment of the MASTR III base station wasperformed prior to shipment. The factory assumed thefollowing characteristic
LBI-38636S27Table 6 - System DeviationSystemDeviationStandard (25 Hz kHz Bandwidth 3.75 kHzNPSPAC 3.0 kHzNarrow (12.5 kHz Bandwidth) 1.75 kHz• Remove
LBI-38636S285. Line Input Sensitivity and Compression• If not a remote station, set the DSP Line InDLI Pot to 0.• If a remote station, do the follo
LBI-38636S29AUDIO ROUTING ANDADJUSTMENTSOnce the T/R Shelf is installed and programmedproperly, audio level adjustments may be made for propersystem o
LBI-38636S30
LBI-38636S4TABLE OF CONTENTSPagePRODUCT SPECIFICATION FOR CE MARKED EQUIPMENT ...
LBI-38636S31
LBI-38636S32Figure 16 - T/R Shelf Interface Board
LBI-38636S33
LBI-38636S34
LBI-38636S35Figure 17 - T/R Shelf Interface Board (Rev. A)
LBI-38636S36
LBI-38636S37
LBI-38636S38Figure 18 - T/R Shelf Interface Board ( Rev. C)
LBI-38636N39REMOTE CONTROLLER TO STATIONCONTROL PANEL ADJUSTMENTSAlthough audio levels should be considered on asystem basis, it is appropriate to set
LBI-38636S40REPEATER PANEL INSTALLATIONCSI Model 32 Repeater PanelUse the following information in Table 11 toconfigure the MASTR III base station whe
LBI-38636S5ILLUSTRATIONSPageFigure 1 - Typical 37-inch MASTR III Stations...
LBI-38636S41Table 11 - CSI-32 Repeater Panel ConnectionsCSI-32J3SIGNAL NAME FUNCTIONMASTR IIICONNECTIONPin 1 A+/(DC Power) P5.1Pin 2 SYS_VOL \SQ_HI/Re
LBI-38636S42ACCESSORIESThe following accessories for the MASTR III Station may be obtained from your local dealer or by calling M/A-COMAfter Market Se
LBI-38636S43This Page Intentionally Blank
INTERCONNECTION DIAGRAM LBI-38636S35MASTR III STATIONT/R SHELF INTERCONNECT(19D903635, Sh. 1, Rev. 4A)
LBI-38636S INTERCONNECTION DIAGRAM36MASTR III STATIONANTENNA CONFIGURATION INTERCONNECT(19D903635, Sh. 2, Rev. 6)MASTR III STATIONAUXILIARY RECEIVER I
INTERCONNECTION DIAGRAM LBI-38636S37MASTR III STATIONEMERGENCY POWER INTERCONNECT(19D903635, Sh. 3, Rev. 2)
LBI-38636S INTERCONNECTION DIAGRAM38MASTR III STATIONGETC/VG INTERCONNECT(19D904268, Rev. 4)
INTERCONNECTION DIAGRAM LBI-38636S39MASTR III STATIONSCAT(188D5683, Rev. 2)
LBI-38636S INTERCONNECTION DIAGRAM40MASTR III STATIONBACK-TO-BACK REPEATER HARNESS(19B803976, Rev. 1)MASTR III STATIONBACK-TO-BACK REPEATER(19B804016,
LBI-38636S41(Intentionally Left Blank)
LBI-38636S6MAXIMUM PERMISSIBLE EXPOSURE (MPE) LIMITSDo not transmit with this basestation and antenna when persons are within the MPE Radius of the an
M/A-COM Wireless Systems3315 Old Forest RoadLynchburg, Virginia 24501(Outside USA, 434-385-2400) Toll Free 800-528-7711www.macom-wireless.com Printed
LBI-38636S7• American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the Measurement ofPotentially Hazardous Electromagnet
LBI-38636S8STATION SPECIFICATIONS(GENERAL)CABINET37-INCH 69-INCHHeight 37.0 inches 69.1 inchesWidth 21.5 inches 23.1 inchesDepth 18.25 inches 21.0 i
LBI-38636S9PUBLICATIONS INDEXMASTR III BASE STATION Systems Combination Package..... LBI-3877
LBI-38636S10NOTE: Indented maintenance manuals are included with the header (cover) maintenance manual.
Comments to this Manuals